» Schneider Electric » Variable Speed Drives » Altivar 71 » Schneider ATV71EXC2C13Y

Schneider ATV71EXC2C13Y


The price is not final. Please check with the manager!

Schneider Electric enclosed variable speed drive ATV71 Plus – 132 kW – 690 V – IP23

Ask a Question


Range of productAltivar 71 Plus
Product or component typeVariable speed drive
Device short nameATV71 Plus
Product destinationSynchronous motors
Asynchronous motors
Product specific applicationComplex, high-power machines
Assembly styleIn floor-standing enclosure compact version
product compositionA switch and fast-acting semi-conductor fuses
An IP65 remote mounting kit for graphic display terminal
Terminals/bars for motor connection
ATV71HC13Y drive on heatsink
A wired ready-assembled Sarel Spacial 6000 enclosure
A line choke
EMC filterIntegrated
Network number of phases3 phases
rated supply voltage690 V +/- 10 %
Supply voltage limits621…759 V
Supply frequency50…60 Hz +/- 5 %
Network frequency47.5…63 Hz
Motor power kW132 kW at 690 V
Line current137 A for 690 V / 132 kW
Apparent power164 kVA for 690 V / 132 kW
Prospective line Isc100 kA with external fuses
Continuous output current150 A at 2.5 kHz, 690 V / 132 kW
Maximum transient current225 A for 60 s / 132 kW
Speed drive output frequency0…500 Hz
Nominal switching frequency2.5 kHz
Switching frequency2.5…4.9 kHz with derating factor
2…4.9 kHz adjustable
Speed range1…100 in open-loop mode, without speed feedback
Speed accuracy+/- 0.01 % of nominal speed in closed-loop mode with encoder feedback 0.2 Tn to Tn
+/- 10 % of nominal slip without speed feedback 0.2 Tn to Tn
Torque accuracy+/- 15 % in open-loop mode, without speed feedback
+/- 5 % in closed-loop mode with encoder feedback
Transient overtorque170 % of nominal motor torque +/- 10 % for 60 s
220 % of nominal motor torque +/- 10 % for 2 s
Braking torque<= 150 % with braking or hoist resistor
30 % without braking resistor
Asynchronous motor control profileFlux vector control with sensor, standard
Flux vector control without sensor, ENA (energy Adaptation) system
Voltage/frequency ratio, 5 points
Flux vector control without sensor, 2 points
Voltage/frequency ratio – Energy Saving, quadratic U/f
Flux vector control without sensor, standard
Voltage/frequency ratio, 2 points
Synchronous motor control profileVector control with sensor, standard
Vector control without sensor, standard
Regulation loopAdjustable PI regulator
Motor slip compensationNot available in voltage/frequency ratio (2 or 5 points)
Automatic whatever the load
Overvoltage categoryClass 3 conforming to EN 50178
Local signallingLCD display unit for operation function, status and configuration
Output voltage<= power supply voltage
IsolationElectrical between power and control
type of cable for external connectionIEC cable at 40 °C, copper 70 °C / PVC
Electrical connectionTerminal M10 – 2 x 150 mm² (U/T1, V/T2, W/T3) entry from the bottom
Terminal – 2.5 mm² / AWG 14 (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1…LI6, PWR) entry from the bottom
Terminal M8 – 2 x 120 mm² (L1/R, L2/S, L3/T) entry from the bottom
Motor recommanded cable cross section3 x 70 mm²
Short-circuit protection200 A fuse protection type gI – power supply upstream
SupplyExternal supply: 24 V DC (19…30 V), <1 A
Internal supply for reference potentiometer: 10 V DC (10…11 V), <10 mA
Internal supply: 24 V DC (21…27 V), <100 mA
Analogue input number2
Analogue input typeAI2 software-configurable voltage: 0…10 V DC, 24 V max, impedance: 30000 Ohm, sampling time: 1.5…2.5 ms, resolution: 11 bits
AI1-/Al1+ bipolar differential voltage: +/- 10 V DC, 24 V max, sampling time: 1.5…2.5 ms, resolution: 11 bits + sign
AI2 software-configurable current: 0…20 mA/4…20 mA, impedance: 250 Ohm, sampling time: 1.5…2.5 ms, resolution: 11 bits
Analogue output number1
Analogue output typeSoftware-configurable voltage: (AO1) 0…10 V DC – 470 Ohm – sampling time: 1.5…2.5 ms – resolution: 10 bits
Software-configurable current: (AO1) 0…20 mA/4…20 mA – 500 Ohm – sampling time: 1.5…2.5 ms – resolution: 10 bits
Discrete output number2
Discrete output typeConfigurable relay logic: (R1A, R1B, R1C)NO/NC – 6.5…7.5 ms – 100000 cycles
Configurable relay logic: (R2A, R2B)NO – 6.5…7.5 ms – 100000 cycles
Minimum switching current3 mA at 24 V DC (configurable relay logic)
Maximum switching current5 A at 250 V AC on resistive load – cos phi = 1 (R1, R2)
5 A at 30 V DC on resistive load – L/R = 0 ms (R1, R2)
2 A at 250 V AC on inductive load – cos phi = 0.4 (R1, R2)
2 A at 30 V DC on inductive load – L/R = 7 ms (R1, R2)
Discrete input number7
Discrete input typeProgrammable (LI1…LI5) at 24 V DC <= 30 V level 1 PLC 3.5 kOhm (duration=1.5…2.5 ms)
Switch-configurable (LI6) at 24 V DC <= 30 V level 1 PLC 1.5 kOhm (duration=1.5…2.5 ms)
Safety input (PWR) at 24 V DC <= 30 V 1.5 kOhm
Discrete input logicPositive logic (source) (LI1…LI6), 0…5 V (state 0), 11…30 V (state 1)
Negative logic (sink) (LI1…LI6), 16…30 V (state 0), 0…10 V (state 1)
Positive logic (source) (PWR), 0…2 V (state 0), 17…30 V (state 1)
Acceleration and deceleration rampsLinear adjustable separately from 0.01 to 9000 s
S, U or customized
Automatic adaptation of ramp if braking capacity exceeded, by using resistor
Braking to standstillBy DC injection
Protection typeAgainst exceeding limit speed: drive
Against input phase loss: drive
Break on the control circuit: drive
Input phase breaks: drive
Line supply overvoltage: drive
Line supply undervoltage: drive
Overcurrent between output phases and earth: drive
Overheating protection: drive
Overvoltages on the DC bus: drive
Short-circuit between motor phases: drive
Thermal protection: drive
Input phase breaks: motor
Power removal: motor
Thermal protection: motor
Dielectric strength3110 V DC between earth and power terminals
5345 V DC between control and power terminals
Insulation resistance> 1 mOhm 500 V DC for 1 minute to earth
Frequency resolutionAnalog input: 0.024/50 Hz
Display unit: 0.1 Hz
communication port protocolCANopen
Connector type1 RJ45 (on front face) for Modbus
1 RJ45 (on terminal) for Modbus
Male SUB-D 9 on RJ45 for CANopen
Physical interface2-wire RS 485 for Modbus
Transmission frameRTU for Modbus
Transmission rate4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal
9600 bps, 19200 bps for Modbus on front face
20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen
Data format8 bits, 1 stop, even parity for Modbus on front face
8 bits, odd even or no configurable parity for Modbus on terminal
Type of polarizationNo impedance for Modbus
Number of addresses1…247 for CANopen
1…247 for Modbus
Method of accessSlave CANopen
Option cardCommunication card for CC-Link
Communication card for DeviceNet
Communication card for EtherNet/IP
Communication card for Fipio
Communication card for Interbus-S
Communication card for Modbus Plus
Communication card for Modbus/Uni-Telway
Communication card for Profibus DP
Communication card for Profibus DP V1
Communication card for Modbus TCP/IP
Controller inside programmable card
Basic I/O extension card
Extended I/O extension card
Encoder interface cards
options for enclosure configurationSafe standstill for power circuit
PTC relay for power circuit
Pt100 relay for power circuit
Insulation monitoring for power circuit
Design for IT networks for power circuit
External 230 V supply terminals for power circuit
Buffer voltage 24 V DC power supply for power circuit
External 24 V DC supply terminals for power circuit
Enclosure lighting for power circuit
Key switch (local/remote) for power circuit
Motor heating for power circuit
External motor fan for power circuit
Voltmeter for power circuit
Door handle for main switch for power circuit
Circuit breaker for power circuit
Line contactor for power circuit
Ammeter for power circuit
Enclosure heating for power circuit
Motor choke for power circuit
Cable entry via the top for power circuit
Enclosure plinth for power circuit
Braking unit for power circuit
Door handle for circuit breaker for power circuit
Control terminals for control circuit
Adaptor for 115 V logic inputs for control circuit
Relay output C/O for control circuit
Isolated amplifier for control circuit
Operating positionVertical +/- 10 degree
Colour of enclosureLight grey (RAL 7035)
Height2162 mm
Width600 mm
Depth642 mm
Net weight415 kg
Electromagnetic compatibility1.2/50 µs – 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5
Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6
Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4
Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2
Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3
Voltage dips and interruptions immunity test conforming to IEC 61000-4-11
Pollution degree2 conforming to EN/IEC 61800-5-1
IP degree of protectionIP23
Vibration resistance0.6 gn (f= 10…200 Hz) conforming to EN/IEC 60068-2-6
1.5 mm (f= 3…10 Hz) conforming to EN/IEC 60068-2-6
3M3 conforming to EN/IEC 60721-3-3
Shock resistance4 gn for 11 ms conforming to EN/IEC 60068-2-27
3M2 conforming to EN/IEC 60721-3-3
Noise level64 dB conforming to 86/188/EEC
Environmental characteristicWithout condensation: 3C2 conforming to IEC 60721-3-3
Without condensation: 3K3 conforming to IEC 60721-3-3
Without condensation: 3S2 conforming to IEC 60721-3-3
Relative humidity0…95 %
Ambient air temperature for operation0…40 °C (without derating)
40…50 °C (with current derating of 0.6 % per °C)
Ambient air temperature for storage-25…70 °C
Volume of cooling air600 m3/h
Operating altitude<= 1000 m without derating
1000…3000 m with current derating 1 % per 100 m
StandardsEN 61800-3 environments 2 category C3
EN/IEC 61800-5-1
EN 61800-3 environments 1 category C3
EN 55011 class A group 2
EN/IEC 61800-3
Product certificationsATEX
Packing Units
Unit Type of Package 1PCE
Number of Units in Package 11
Package 1 Height216.0 cm
Package 1 Width66.0 cm
Package 1 Length61.6 cm
Package 1 Weight415.0 kg
Contractual warranty
Warranty18 months

Leave a Reply

Your email address will not be published. Required fields are marked *


Reviews about the product Schneider ATV71EXC2C13Y